InSight’s seismometer package SEIS was placed on the surface of Mars at about 1.2 m distance from the thermal properties instrument HP3 that includes a self-hammering probe. Recording the hammering noise with SEIS provided a unique opportunity to estimate the seismic wave velocities of the shallow regolith at the landing site. However, the value of studying the seismic signals of the hammering was only realised after critical hardware decisions were already taken. Furthermore, the design and nominal operation of both SEIS and HP3 are non-ideal for such high-resolution seismic measurements. Therefore, a series of adaptations had to be implemented to operate the self-hammering probe as a controlled seismic source and SEIS as a high-frequency seismic receiver including the design of a high-precision timing and an innovative high-frequency sampling workflow. By interpreting the first-arriving seismic waves as a P-wave and identifying first-arriving S-waves by polarisation analysis, we determined effective P- and S-wave velocities of vP = 119+45-21 m/s and vS = 63+11-7 m/s, respectively, from around 2,000 hammer stroke recordings. These velocities likely represent bulk estimates for the uppermost several 10’s of cm of regolith. An analysis of the P-wave incidence angles provided an independent vP/vS ratio estimate of 1.84+0.89-0.35 that compares well with the traveltime based estimate of 1.86+0.42-0.25. The low seismic velocities are consistent with those observed for low-density unconsolidated sands and are in agreement with estimates obtained by other methods.

In 2007, the National Academies designated “understanding the structure & composition of the lunar interior” (to provide fundamental information on the evolution of a differentiated planetary body) as the second highest lunar science priority that needed to be addressed. Here we present the current status of the planned response of the Lunar Geophysical Network (LGN) team to the upcoming New Frontiers-5 AO. The Moon represents an end-member in the differentiation of rocky planetary bodies. Its small size (and heat budget) means that the early stages of differentiation have been frozen in time. But despite the success of the Apollo Lunar Surface Experiment Package (ALSEP), significant unresolved questions remain regarding the nature of the lunar interior and tectonic activity. General models of the processes that formed the present-day lunar interior are currently being challenged. While reinterpretation of the Apollo seismic data has led to the identification of a lunar core, it has also produced a thinning of the nearside lunar crust from 60-65 km in 1974 to 30-38 km today. With regard to the deep mantle, Apollo seismic data have been used to infer the presence of garnet below ~500 km, but the same data have also been used to identify Mg-rich olivine. A long-lived global lunar geophysical network (seismometer, heat flow probe, magnetometer, laser retro-reflector) is essential to defining the nature of the lunar interior and exploring the early stages of terrestrial planet evolution, add tremendous value to the GRAIL and SELENE gravity data, and allow other nodes to be added over time (ie, deliver the International Lunar Network). Identification of lateral and vertical heterogeneities, if present within the Moon, will yield important information about the early presence of a global lunar magma ocean (LMO) as well as exploring LMO cumulate overturn. LGN would also provide new constraints on seismicity, including shallow moonquakes (the largest type identified by ALSEP with magnitudes between 5-6) that have been linked to young thrust fault scarps, suggesting current tectonic activity. Advancing our understanding of the Moon’s interior is critical for addressing these and many other important lunar and Solar System science and exploration questions, including protection of astronauts from the strong shallow moonquakes.

The InSight mission (Interior Exploration using Seismic Investigations, Geodesy and Heat Transport) has been collecting high-quality seismic data from Mars since February 2019, shortly after its landing. The Marsquake Service (MQS) is the team responsible for the prompt review of all seismic data recorded by the InSight’s seismometer (SEIS), marsquake event detection, and curating seismicity catalogues. Until sol 1011 (end of September 2021), MQS have identified 951 marsquakes that we interpret to occur at regional and teleseismic distances, and 1062 very short duration events that are most likely generated by local thermal stresses nearby the SEIS package. Here, we summarize the seismic data collected until sol 1011, version 9 of the InSight seismicity catalogue. We focus on the significant seismicity that occurred after sol 478, the end date of version 3, the last catalogue described in a dedicated paper. In this new period, almost a full Martian year of new data has been collected, allowing us to observe seasonal variations in seismicity that are largely driven by strong changes in atmospheric noise that couples into the seismic signal. Further, the largest, closest and most distant events have been identified, and the number of fully located events has increased from 3 to 7. In addition to the new seismicity, we document improvements in the catalogue that include the adoption of InSight-calibrated Martian models and magnitude scales, the inclusion of additional seismic body-wave phases, and first focal mechanism solutions for three of the regional marsquakes at distances ~30 degrees.

Distributed sensor networks empower real-time in-situ computing and seismic imaging without transmitting the raw data to the remote data center. This attribute is valuable for planet exploration that has stringent bandwidth. The previously distributed ambient noise imaging algorithm computes results using data from near neighbors, while the information from distant neighbors is not utilized, hence the image quality is compromised. To overcome this problem, this work proposes an innovative common-receiver-based decentralized ambient noise imaging algorithm. In this algorithm, the basic imaging algorithm is still Eikonal tomography, but the distant neighbors are also used to computing the seismic image so that the quality of the output image can be preserved. An in-situ computing and clustering algorithm is created to optimize the data transition and computation while meeting the bandwidth constrains. The experiments were performed on both synthetic data from Enceladus and real data from the USArray archives. The new algorithm generates higher-resolution images under the same bandwidth constraints, comparing to previous algorithms, and the quality of the output image is satisfactorily preserved. The communication cost reduction over the raw data collection is in several orders of magnitude (e.g., 1: 1600). It meets the desired bandwidth constraint in planetary exploration applications.

The NASA InSight lander successfully placed a seismometer on the surface of Mars. Alongside, a hammering device was deployed that penetrated into the ground to attempt the first measurements of the planetary heat flow of Mars. The hammering of the heat probe generated repeated seismic signals that were registered by the seismometer and can potentially be used to image the shallow subsurface just below the lander. However, the broad frequency content of the seismic signals generated by the hammering extends beyond the Nyquist frequency governed by the seismometer's sampling rate of 100 samples per second. Here, we propose an algorithm to reconstruct the seismic signals beyond the classical sampling limits. We exploit the structure in the data due to thousands of repeated, only gradually varying hammering signals as the heat probe slowly penetrates into the ground. In addition, we make use of the fact that repeated hammering signals are sub-sampled differently due to the unsynchronised timing between the hammer strikes and the seismometer recordings. This allows us to reconstruct signals beyond the classical Nyquist frequency limit by enforcing a sparsity constraint on the signal in a modified Radon transform domain. Using both synthetic data and actual data recorded on Mars, we show how the proposed algorithm can be used to reconstruct the high-frequency hammering signal at very high resolution. In this way, we were able to constrain the seismic velocity of the top first meter of the Martian regolith.